AFHKC SERIES (2-STAGE)
Hypoid- Special design for continuous (S1) or cyclic (S5) duty operation
- Stainless steel housing, aluminum black anodized motor adapter flange
- Stainless steel output shaft with or without key, or with spline (DIN5480)
- Helical gear design
- Nominal torques:
- T2N : 60 Nm - 4,260 Nm
- Ratios
- 2-stage : 4 / 5 / 7 / 8 / 10
- Low backlash
- 2-stage : ≤ 2 arcmin / ≤ 3 arcmin
- High efficiency
- 2-stage : ≥ 95%
- Easy mount
- Low noise
- Compact structure
- Sizes available: AFHKC075 / AFHKC100 / AFHKC140 / AFHKC180 / AFHKC210 / AFHKC240
| Model No. | Stage | Ratio¹ | AFHKC060 | AFHKC075 | AFHKC100 | AFHKC140 | AFHKC180 | AFHKC210 | AFHKC240 | |
| Nominal Output Torque T2N | Nm | 2 | 4 | 100 | 205 | 380 | 775 | 1,440 | 2,240 | 4,160 |
| 5 | 85 | 185 | 330 | 670 | 1,250 | 1,930 | 3,610 | |||
| 7 | 60 | 135 | 260 | 525 | 1,000 | 1,750 | 2,535 | |||
| 8 | 96 | 205 | 395 | 800 | 1,320 | 2,300 | 4,260 | |||
| 10 | 90 | 165 | 340 | 690 | 1,290 | 2,000 | 3,700 | |||
| Emergency Stop Torque T2Not | Nm | 2 | 4~10 | 2 times T2N | ||||||
| Max. Acceleration Torque T2b | Nm | 2 | 4~10 | 1.5 times T2N | ||||||
| No Load Running Torque(2) | NM | 2 | 4~10 | 2 | 2.5 | 5.8 | 12 | 25 | 48 | 95 |
| Backlash(3) | arcmin | 2 | 4~10 | ≤3 | ≤2 | ≤2 | ≤2 | ≤2 | ≤2 | ≤2 |
| Torsional Rigidity | Nm/arcmin | 2 | 4~10 | 4.6 | 10 | 30 | 55 | 175 | 300 | 510 |
| Nominal Input Speed n1N | rpm | 2 | 4~10 | 5,000 | 3,600 | 3,000 | 2,300 | 1,800 | 1,500 | 1,100 |
| Max. Input Speed | rpm | 2 | 4~10 | 7,000 | 6,000 | 5,500 | 4,500 | 3,500 | 3,000 | 2,200 |
| Max. Radial Load F2r(4) | 4~10 | 3,000 | 4,500 | 6,700 | 10,000 | 15,000 | 22,000 | 30,000 | ||
| Max. Axial Load F2a(4) | N | 2 | 4~10 | 1,500 | 2,250 | 3,350 | 5,000 | 7,500 | 11,000 | 15,000 |
| Max. Tilting Moment M2k(4) | Nm | 2 | 4~10 | 160 | 270 | 550 | 1,050 | 1,740 | 3,350 | 5,420 |
| Operating Temp. | °C | 2 | 4~10 | -10º C~ 90º C | ||||||
| Degree of Gearbox Protection | 2 | 4~10 | IP65 | |||||||
| Lubrication | 2 | 4~10 | Synthetic lubrication grease | |||||||
| Mounting Position | 2 | 4~10 | All directions | |||||||
| Running Noise (5) | dB(A) | 2 | 4~10 | ≤68 | ≤68 | ≤68 | ≤70 | ≤70 | ≤72 | ≤74 |
| Efficiency | % | 2 | 4~10 | ≥94% | ||||||
(1) Ratio ( i = N in / N out)
(2) These values are measured by gearbox with ratio 10 (2-stage) at 3,000 rpm no loading.
(3) Backlash is measured at 2% of Nominal Output Torque T2N
(4) Applied to the output shaft center at 100 rpm.
(5) These values are measured by gearbox with ratio 10 (2-stage) at 3,000 rpm no loading.
By lower ratio and/or higher RPM, the noise level could be 3 to 5 dB higher.
| Model No. | AFHKC060 | AFHKC075 | AFHKC100 | AFHKC140 | AFHKC180 | AFHKC210 | AFHKC240 | |
| Ø(1) | stage | 2-st | 2-st | 2-st | 2-st | 2-st | 2-st | 2-st |
| 8 | kg.cm2 | 0.10 | - | - | - | - | - | - |
| 11 | 0.16 | 0.41 | - | - | - | - | - | |
| 14 | 0.20 | 0.41 | - | - | - | - | - | |
| 19 | 0.58 | 1.61 | 1.61 | - | - | - | - | |
| 24 | - | 3.9 | 4.01 | 5.62 | - | - | - | |
| 28 | - | - | 5.53 | 5.62 | - | - | - | |
| 32 | - | - | 7.57 | 8.11 | 8.11 | - | - | |
| 35 | - | - | 14.95 | 15.32 | 15.32 | 15.68 | 19.37 | |
| 38 | - | - | 17.58 | 17.72 | 17.72 | 18.52 | 19.37 | |
| 42 | - | - | - | 22.95 | 22.95 | 23.74 | 25.5 | |
| 48 | - | - | - | 52.74 | 52.74 | 53.49 | 55.14 | |
| 55 | - | - | - | - | - | 87.34 | 89.59 | |
| 60 | - | - | - | - | - | - | 113.06 | |
(1) Ø = Input shaft diameter.
| AFHKC060 | AFHKC075 | AFHKC100 | AFHKC140 | AFHKC180 | AFHKC210 | AFHKC240 | |
| D1 | 68 | 85 | 120 | 165 | 215 | 250 | 290 |
| D2 | 5.5 | 7 | 9 | 11 | 13.5 | 17 | 17 |
| D3 h6 | 16 | 22 | 32 | 40 | 55 | 75 | 85 |
| D4 g6 | 60 | 70 | 90 | 130 | 160 | 180 | 200 |
| D5 | 18.5 | 25.8 | 36.8 | 55.2 | 69.2 | 82.2 | 92.2 |
| D6 | M5 x 0.8P | M8 x 1.25P | M12 x 1.75P | M16 x 2P | M20 x 2.5P | M20 x 2.5P | M20 x 2.5P |
| D7 h6 | 16 | 22 | 32 | 40 | 55 | 75 | 85 |
| D8 | 64 | 92 | 116 | 156 | 156 | 195 | 240 |
| D9 H6 | 15 | 20 | 30 | 40 | 55 | - | - |
| D10 h8 | 18 | 24 | 36 | 50 | 68 | - | - |
| L1 | 62 | 76 | 101 | 141 | 182 | 215 | 245 |
| L2 | 28 | 36 | 58 | 82 | 82 | 105 | 130 |
| L3 | 20 | 20 | 30 | 30 | 30 | 38 | 40 |
| L4 | 2 | 2.5 | 3 | 3 | 3 | 3 | 3 |
| L5 | 25 | 32 | 50 | 63 | 70 | 90 | 125 |
| L6 | 2 | 2 | 4 | 5 | 6 | 7 | 3 |
| L7 | 6 | 7 | 10 | 12 | 15 | 17 | 22 |
| L9 | 4.8 | 7.2 | 10 | 12 | 15 | 15 | 15 |
| L10 | 12.5 | 19 | 28 | 36 | 42 | 42 | 42 |
| L11 | 121.5 | 145.5 | 163 | 219 | 258 | 277.5 | 352 |
| L12 | 46.5 | 61.5 | 76 | 97.5 | 97.5 | 105.5 | 141 |
| L13 | 216 | 263 | 327 | 428.5 | 467.5 | 526 | 663 |
| L16 | 81.5 | 113.5 | 147.5 | 196.5 | 196.5 | 229 | 260 |
| L17 | 26 | 26 | 26 | 40 | 41.5 | 52 | 60 |
| L18 | 15 | 15 | 15 | 20 | 21.5 | 28 | 36 |
| L19 | 21 | 22.5 | 23 | 33.5 | 33.5 | 45 | 53 |
| L20 | 12 | 14 | 18 | 22 | 23 | - | - |
| L21 | 22 | 22 | 32 | 33 | 32 | - | - |
| L22 | 19 | 21 | 25 | 30 | 30 | - | - |
| L23 | 2 | 2.5 | 2.5 | 2.5 | 2.5 | 2.5 | 4 |
| L24 | 0.3 | 0.4 | 0.4 | 0.4 | 0.4 | 0.4 | 0.5 |
| B1 h9 | 5 | 6 | 10 | 12 | 16 | 20 | 22 |
| H1 | 18 | 24.5 | 35 | 43 | 59 | 79.5 | 90 |
| X DINS5480 | W16 x 0.8 x 30 x 18 x 6m |
W22 x 1.25 x 30 x 16 x 6m |
W32 x 1.25 x 30 x 24 x 6m |
W40 x 2 x 30 x 18 x 6m |
W55 x 2 x 30 x 26 x 6m |
W70 x 2 x 30 x 34 x 6m |
W80 x 2 x 30 x 38 x 6m |
(1) Dimensions are related to motor interface. Please contact APEX for details.
Recaptcha | Site by Merkelijkheid.nl