KF | Stage | Ratio(1) | KF 060 |
KF 075 |
KF 100 |
KF 140 |
KF 180 |
KF 210 |
KF 240 |
|
Nominal output torque T2N
|
Nm
|
1 |
3 | 25 | 50 | 110 | 210 | 420 | 820 | 1,600 |
4 | 25 | 60 | 110 | 210 | 420 | 820 | 1,600 | |||
5 | 25 | 60 | 110 | 210 | 420 | 820 | 1,600 | |||
7 | 23 | 50 | 100 | 200 | 390 | 750 | 1,400 | |||
10 | 18 | 40 | 85 | 170 | 360 | 600 | 1,100 | |||
2 |
12 | 25 | 60 | 110 | 210 | 420 | 820 | 1,600 | ||
16 | 25 | 60 | 110 | 210 | 420 | 820 | 1,600 | |||
20 | 25 | 60 | 110 | 210 | 420 | 820 | 1,600 | |||
25 | 25 | 60 | 110 | 210 | 420 | 820 | 1,600 | |||
28 | 25 | 60 | 110 | 210 | 420 | 820 | 1,600 | |||
35 | 25 | 60 | 110 | 210 | 420 | 820 | 1,600 | |||
40 | 25 | 60 | 110 | 210 | 420 | 820 | 1,600 | |||
50 | 25 | 60 | 110 | 210 | 420 | 820 | 1,600 | |||
70 | 23 | 50 | 100 | 200 | 390 | 750 | 1,400 | |||
100 | 18 | 40 | 85 | 170 | 360 | 600 | 1,100 | |||
Emergency stop torque T2NOT | Nm | 1 | 3~10 | 2 times of nominal torque T2N | ||||||
Max. Acceleration torque T2B | Nm | 1 | 3~10 | 1,5 times of nominal torque T2N | ||||||
No load running torque (2) | Nm | 1 | 3~10 | 0.8 | 1.3 | 2.6 | 3.5 | 8 | 11 | 17.6 |
2 | 12~100 | 0.1 | 0.1 | 0.2 | 0.3 | 0.9 | 1.2 | 1.9 | ||
Backlash (3) | arcmin | 1 | 3~10 | ≤3 | ≤3 | ≤3 | ≤3 | ≤3 | ≤3 | ≤3 |
2 | 12~200 | ≤3 | ≤3 | ≤3 | ≤3 | ≤3 | ≤3 | ≤3 | ||
Torsional rigidity | Nm/arcmin | 1,2 | 3~100 | 0.8 | 3.5 | 9 | 20.5 | 44 | 80 | 168 |
Nominal input speed n1N | rpm | 1 | 3~10 | 3,000 | 2,800 | 2,700 | 2,000 | 2,000 | 2,000 | 1,500 |
2 | 12~100 | 5,500 | 4,500 | 4,200 | 3,900 | 3,400 | 2,800 | 2,200 | ||
Max. input speed n1B | rpm | 1 | 3~10 | 6,000 | 6,000 | 4,500 | 4,500 | 4,000 | 3,000 | 2,500 |
2 | 12~100 | 7,000 | 7,000 | 7,000 | 6,000 | 5,500 | 5,000 | 4,500 | ||
Max. radial load F2rB (4) | N | 1,2 | 3~100 | 5,700 | 8,200 | 12,200 | 20,100 | 30,700 | 40,900 | 51,900 |
Max. axial load F2aB (4) | N | 1,2 | 3~100 | 2,850 | 4,100 | 6,100 | 10,050 | 15,350 | 20,450 | 20,950 |
Max. tilting moment M2k | Nm | 1,2 | 3~100 | 310 | 530 | 1,090 | 2,340 | 5,400 | 9,700 | 15,200 |
Operating temperature | °C | 1,2 | 3~100 | 0° C ~ +90°C | ||||||
Degree of Protection | 1,2 | 3~100 | IP65 | |||||||
Lubrication | 1,2 | 3~100 | Synthetisch lubrication grease | |||||||
Mounting position | 1,2 | 3~100 | All directions | |||||||
Running noise (5) | dB (A) | 1,2 | 3~100 | ≤64 | ≤66 | ≤66 | ≤68 | ≤68 | ≤70 | ≤72 |
Efficiency n | % | 1 | 3~10 | ≥96% | ||||||
2 | 12~100 | ≥94% |
Maximum tilting moment::
Size | KF060 | KF075 | KF100 | KF140 | KF180 | KF210 | KF240 | |
Z2 (mm) | 96.3 | 111.9 | 150.1 | 192 | 231.1 | 289.2 | 355.1 |
Maximum radial and axial loads:
The maximum radial and axial loads on the output shaft of the gearbox depends on the design of the gearbox supporting bearings.
Apex Dynamics uses the extension straddle oversized ball bearing design. This can take heavy load from both axles
Permitted radial load F2r on center of output shaft X = ½ x L for various output speeds.
If radial force F2r is not exerted on the center of the ouput shaft X < ½ x L or X > ½ x L, the permitted radial and axial loads can be calculated by the position load factor Kb on the above diagram.
Model No. | KF 060 |
KF 075 |
KF 100 |
KF 140 |
KF 180 |
KF 210 |
KF 240 |
||||||||
Ø (A) (C3) | 1-stage | 2-stage | 1-stage | 2-stage | 1-stage | 2-stage | 1-stage | 2-stage | 1-stage | 2-stage | 1-stage | 2-stage | 1-stage | 2-stage | |
8 |
kg*cm2 |
0.10 | 0.10 | - | - | - | - | - | - | - | - | - | - | - | |
11 | 0.17 | 0.16 | 0.18 | 0.17 | - | - | - | - | - | - | - | - | - | - | |
14 | 0.21 | 0.20 | 0.50 | 0.21 | - | 0.53 | - | - | - | - | - | - | - | - | |
19 | 0.62 | - | 0.63 | 0.63 | 1.69 | 0.68 | - | 1.83 | - | - | - | - | - | - | |
24 | - | - | 4.49 | - | 4.89 | 4.52 | 5.05 | 5.04 | - | 5.63 | - | - | - | - | |
28 | - | - | - | - | 6.14 | - | 6.55 | 6.33 | - | 7.18 | - | - | - | - | |
32 | - | - | - | - | 8.54 | - | 9.47 | 8.73 | 10.18 | 10.1 | - | 12.63 | - | - | |
35 | - | - | - | - | 13.86 | - | 14.91 | 14.04 | 15.21 | 15.54 | 15.68 | 17.75 | 23.46 | 20.80 | |
38 | - | - | - | - | 18.87 | - | 20.69 | 19.05 | 20.7 | 21.32 | 21.69 | 23.26 | 23.46 | 27.05 | |
42 | - | - | - | - | - | - | 22.58 | - | 22.83 | 23.2 | 23.59 | 25.40 | 25.28 | 28.95 | |
48 | - | - | - | - | - | - | 55.45 | - | 58.45 | 56.07 | 25.40 | 61.02 | 61.61 | 64.66 | |
55 | - | - | - | - | - | - | - | - | - | - | 61.02 | - | 89.67 | - | |
60 | - | - | - | - | - | - | - | - | - | - | - | - | 112.49 | - |
(A) Ø Input shaft diameter
KF-S1 / S2 / S3:
KF 060 | KF 075 | KF 100 | KF 140 | KF 180 | KF 210 | KF 240 | |
1~2-stage | 1~2-stage | 1~2-stage | 1~2-stage | 1~2-stage | 1~2-stage | 1~2-stage | |
D1 | 68 | 85 | 120 | 165 | 215 | 250 | 290 |
D2 | 5.5 | 6.6 | 9 | 11 | 13.5 | 17 | 17 |
D3 h6 | 16 | 22 | 32 | 40 | 55 | 75 | 85 |
D4 g6 | 60 | 70 | 90 | 130 | 160 | 180 | 200 |
D5 | 18.5 | 25.8 | 36.8 | 55.2 | 69.2 | 82.2 | 92.2 |
D6 | M5x0.8P | M8x1.25P | M12x1.75P | M16x2P | M20x2.5P | M20x2.5P | M20x2.5P |
D7 h6 | 16 | 22 | 32 | 40 | 55 | 75 | 85 |
D8 | 73 | 94 | 116 | 163 | 210 | 255 | 300 |
L1 | 62 | 76 | 101 | 141 | 182 | 215 | 245 |
L2 | 28 | 36 | 58 | 82 | 82 | 105 | 130 |
L3 | 20 | 20 | 30 | 30 | 30 | 38 | 40 |
L4 | 2 | 2,5 | 3 | 3 | 3 | 3 | 3 |
L5 | 25 | 32 | 50 | 63 | 70 | 90 | 125 |
L6 | 2 | 2 | 4 | 5 | 6 | 7 | 3 |
L7 | 6 | 7 | 10 | 12 | 15 | 17 | 20 |
L8 | 10 | 13 | 17 | 25 | 31 | 36 | 43 |
L9 | 4.8 | 7.2 | 10 | 12 | 15 | 15 | 15 |
L10 | 12.5 | 19 | 28 | 36 | 42 | 42 | 42 |
L11 | 43 | 53.5 | 67 | 90 | 119 | 141 | 176 |
L12 | 44.5 | 53 | 68.3 | 89 | 115 | 131 | 165 |
L13 | 135.5 | 162.5 | 223.3 | 291 | 346 | 415 | 511 |
L16 | 94 | 114,5 | 129 | 173.5 | 228 | 265.5 | 294.5 |
L17 | 26 | 26 | 26 | 40 | 41,5 | 52 | 60 |
L18 | 15 | 15 | 15 | 20 | 21,5 | 28 | 36 |
L19 | 21 | 22,5 | 23 | 33,5 | 33,5 | 45 | 53 |
B1 h9 | 5 | 6 | 10 | 12 | 16 | 20 | 22 |
H1 | 18 | 24,5 | 35 | 43 | 59 | 79,5 | 90 |
X DIN 5480 |
W16x0.8x30x18x6m | W22x1.25x30x16x6m | W32x1.25x30x24x6m | W40x2x30x18x6m | W55x2x30x26x6m | W70x2x30x34x6m | W80x2x30x38x6m |
(1) Dimensions are related to motor interface. Please contact Apex Dynamics for details.
Model No. | Dimension | D1 | D2 | D3 | H1 | H2 | Screw(1) | Ta (2) | J | Order Code |
No. x type | (Nm) | (kg.CM2) | ||||||||
KF 060 | SSD-d18xdw15 | 44 | 18 | 30 | 15 | 18.5 | 5 x M5 | 4 | 0.4 | SSD-18 |
KF 075 | SSD-d24xdw20 | 50 | 24 | 36 | 19.5 | 23 | 6 x M5 | 4 | 0.8 | SSD-24 |
KF 100 | SSD-d36xdw30 | 72 | 36 | 52 | 23.5 | 27.5 | 5 x M6 | 12 | 3.9 | SSD-36 |
KF 140 | SSD-d50xdw40 | 90 | 50 | 70 | 27.5 | 31.5 | 8 x M6 | 12 | 11.2 | SSD-50 |
KF 180 | SSD-d68xdw55 | 115 | 68 | 86 | 30.5 | 34.5 | 10 x M6 | 12 | 30.9 | SSD-68 |
Need help with your application? Our specialists are happy to use their years of experience to assist you in selecting the right products.