• Black coated steel housing, aluminum output and motor adapter flange
  • Steel output shaft, smooth
  • Hypoid gear design
  • Nominal torques:
    • T2N : 18 Nm - 1.600 Nm
  • Ratios
    • 1-stage : 3 / 4 / 5 / 7 / 10
    • 2-stage : 12 / 16 / 20 / 25 / 28 / 35 / 40 / 50 / 70 / 100
  • Low backlash
    • 1-stage : ≤ 3 arcmin
    • 2-stage : ≤ 3 arcmin
  • High efficiency
    • 1-stage : ≥ 96%
    • 2-stage : ≥ 94%
  • Easy mount
  • High accuracy
  • The output shaft rotates in the same direction as the servomotor
  • Available sizes: KF060 / KF075 / KF100 / KF140 / KF180 / KF210 / KF240
KF Stage Ratio(1) KF
060
KF
075
KF
100
KF
140
KF
180 
KF
210
KF
240
 

Nominal output torque T2N

 

 

Nm

 

 

 

1

3 25 50 110 210 420 820 1,600
4 25 60 110 210 420 820 1,600
5 25 60 110 210 420 820 1,600
7 23 50 100 200 390 750 1,400
10 18 40 85 170 360 600 1,100
 

2

12 25 60 110 210 420 820 1,600
16 25 60 110 210 420 820 1,600
20 25 60 110 210 420 820 1,600
25 25 60 110 210 420 820 1,600
28 25 60 110 210 420 820 1,600
35 25 60 110 210 420 820 1,600
40 25 60 110 210 420 820 1,600
50 25 60 110 210 420 820 1,600
70 23 50 100 200 390 750 1,400
100 18 40 85 170 360 600 1,100
Emergency stop torque T2NOT Nm 1 3~10 2 times  of nominal torque T2N
Max. Acceleration torque T2B Nm 1 3~10 1,5 times  of nominal torque T2N
No load running torque (2) Nm 1 3~10 0.8 1.3 2.6 3.5 8 11 17.6
2 12~100 0.1 0.1 0.2 0.3 0.9 1.2 1.9
Backlash (3) arcmin 1 3~10 ≤3 ≤3 ≤3 ≤3 ≤3 ≤3 ≤3
2 12~200 ≤3 ≤3 ≤3 ≤3 ≤3 ≤3 ≤3
Torsional rigidity Nm/arcmin 1,2 3~100 0.8 3.5 9 20.5 44 80 168
Nominal input speed n1N rpm 1 3~10 3,000 2,800 2,700 2,000 2,000 2,000 1,500
2 12~100 5,500 4,500 4,200 3,900 3,400 2,800 2,200
Max. input speed n1B rpm 1 3~10 6,000 6,000 4,500 4,500 4,000 3,000 2,500
2 12~100 7,000 7,000 7,000 6,000 5,500 5,000 4,500
Max. radial load F2rB (4) N 1,2 3~100 5,700 8,200 12,200 20,100 30,700 40,900 51,900
Max. axial load F2aB (4) N 1,2 3~100 2,850 4,100 6,100 10,050 15,350 20,450 20,950
Max. tilting moment K2m Nm 1,2 3~100 310 530 1,090 2,340 5,400 9,700 15,200
Operating temperature °C 1,2 3~100 0° C ~ +90°C
Degree of Protection 1,2 3~100 IP65
Lubrication 1,2 3~100 Synthetisch lubrication grease
Mounting position 1,2 3~100 All directions
Running noise (5) dB (A) 1,2 3~100 ≤64 ≤66 ≤66 ≤68 ≤68 ≤70 ≤72
Efficiency n % 1 3~10 ≥96%
2 12~100 ≥94%
  1. Overbrengverhouding ( i = N in / N out ) Ratio ( i = N in / N out )
  2. Backlash is measured at 2% of Nominal output torque T2N
  3. These values are measured by gearbox with ratio = 10 (1-stage) or ratio = 100 (2-stage) at 3.000 rpm without load.
  4. Applied to the ourput flange center at 100 rpm.
  5. These values are measured by gearbox with ratio 10 (1-stage) or ratio 100 (2-stage) at 3,000 rpm no loading.
    By lower ratio and/or higher RPM, the noise level could be 3 to 5 dB higher.

Maximum tilting moment::

KF Tilting Moment

 

 

 

Max Tilting Moment

 

 

 

 

Size KF060 KF075 KF100 KF140 KF180 KF210 KF240
Z2 (mm) 96.3 111.9 150.1 192 231.1 289.2 355.1
    Applied to the ourput flange center at 100 rpm.

Maximum radial and axial loads:

AB axial load as

 

 

 

 

 

 

 

 

The maximum radial and axial loads on the output shaft of the gearbox depends on the design of the gearbox supporting bearings.
Apex Dynamics uses the extension straddle oversized ball bearing design. This can take heavy load from both axles

KF radial load grafiek

 

 

 

 

 

 

 

 

 

 

Permitted radial load F2r on center of output shaft X = ½ x L for various output speeds.

KF position load grafiek

 

 

 

 

 

 

 

 

 

 

If radial force F2r is not exerted on the center of the ouput shaft X < ½ x L or X > ½ x L, the permitted radial and axial loads can be calculated by the position load factor Kb on the above diagram.


Download as PDF

Model No. KF 060
 
KF 075
 
KF 100
 
KF 140
 
KF 180
 
KF 210
 
KF 240

Ø (A) (C3) 1-stage 2-stage 1-stage 2-stage 1-stage 2-stage 1-stage 2-stage 1-stage  2-stage 1-stage 2-stage 1-stage 2-stage
8  

 

 

 

 

kg*cm2

0.10 0.10 - - - - - - - - - - -
11 0.17 0.16 0.18 0.17 - - - - - - - - - -
14 0.21 0.20 0.50 0.21 - 0.53 - - - - - - - -
19 0.62 - 0.63 0.63 1.69 0.68 - 1.83 - - - - - -
24 - - 4.49 - 4.89 4.52 5.05 5.04 - 5.63 - - - -
28 - - - - 6.14 - 6.55 6.33 - 7.18 - - - -
32 - - - - 8.54 - 9.47 8.73 10.18 10.1 - 12.63 - -
35 - - - - 13.86 - 14.91 14.04 15.21 15.54 15.68 17.75 23.46 20.80
38 - - - - 18.87 - 20.69 19.05 20.7 21.32 21.69 23.26 23.46 27.05
42 - - - - - - 22.58 - 22.83 23.2 23.59 25.40 25.28 28.95
48 - - - - - - 55.45 - 58.45 56.07 25.40 61.02 61.61 64.66
55 - - - - - - - - - - 61.02 - 89.67 -
60 - - - - - - - - - - - - 112.49 -

(A) Ø Input shaft diameter


Download as PDF

KF-S4

KF 060 KF 075 KF 100 KF 140 KF 180
1~2-stage 1~2-stage 1~2-stage 1~2-stage 1~2-stage
D1  68 85  120 165  215
D2 5.5 6.6 9 11 13.5
D3 H6 15 20 30 40 55
D4 g6 60 70 90 130 160
D5 18.5 25.8 36.8 55.2 69.2
D8 73 94 116 163 210
D9 18 24 36 50 68
L1 62 76 101 141 182
L2 12 14 18 22 23
L3 22 21.8 32 33 34
L4 4 4.3 5 6 7
L7 6 7 10 12 15
L8 10 13 17 25 31
L11 43 53.5 67 90 119
L12 48.5 57.7 73.3 95 122
L13 137.5 161 208.3 262 321
L14 4 4.7 5 6 7
L15 19 21 25 30 30
L16 94 114.5 129 173.5 228

(1) Dimensions are related to motor interface. Please contact Apex Dynamics for details.

 

Model No.  Dimension D1 D2 D3 H1 H2 Screw(1) Ta (2) J Order Code
No. x type (Nm) (kg.CM2)
KF 060 SSD-d18xdw15 44 18 30 15 18.5 5 x M5 4 0.4 SSD-18
KF 075 SSD-d24xdw20 50 24 36 19.5 23 6 x M5 4 0.8 SSD-24
KF 100 SSD-d36xdw30 72 36 52 23.5 27.5 5 x M6 12 3.9 SSD-36
KF 140 SSD-d50xdw40 90 50 70 27.5 31.5 8 x M6 12 11.2 SSD-50
KF 180 SSD-d68xdw55 115 68 86 30.5 34.5 10 x M6 12 30.9 SSD-68
  1. 10.9 Class, DIN 931
  2. Tightening Torque